![]() (This is needed to get at least partially correct HW info. SMBIOS -> Configure to be `Mac Pro 6,1` using wizard (bottom right button on top pane). ![]() Kernel and kext patches -> check `Asus AICPUPM` (Kernel panic while booting if this is not done) Boot -> Arguments -> check `nv_disable=1` (if you have nvidia GPU) Boot -> Arguments -> check `npci=0x2000` (If this is not done, eventually won't "find root device" after boot process starts) Boot -> Arguments -> check `verbose=1` (show log instead of apple logo when booting) Boot -> Arguments -> check `dart=0` (disables VT-d if it is not disabled in BIOS. Then just add the key and string in the KextandKernelPatches section of Clovers ist during post-installation. The Clover Configurator app is organized around two major functionalities. In addition, Clover Configurator can check for the latest Clover EFI revision, and helps you download and install the bootloader. ACPI -> Fixes -> `FixShutdown_0004` (not sure if this is needed) Go into Clover options at boot time and input the Skylake ID as FakeCPUID. Upon launch, Clover Configurator will check to see if there are already available configuration files, and enables you to view their content. ACPI -> DSDT patches -> add `Change USBE to EH02` (Same here) Also USB won't work when booting already installed OS) ACPI -> DSDT patches -> add `Change EUSB to EH01` (If this is not done, eventually won't "find root device" after boot process starts. (Download clover from internets and install to USB disk destination). Upgrade clover to latest to remove 64Gb RAM cap. using Clover configurator - guide is written for "Clover Vibrant" version) - mount EFI partition, open `/Volumes/EFI/Clover/ist` on right EFI volume (USB or local disk), edit, save. ![]() Create unibeast UEFI USB from sierra 10.12.4 (download from App store)Ĭonfigure clover (e.g. Disable `VT-d` (`VT-x` can stay enabled) Advanced -> Device options -> Set `EFI` for storage and the other one but not to video! (won't get past ` .` when booting if this is not done) My USB 3.0 and Internal Sata are Intel chipset.- Texas instruments TUSB73x0 SuperSpeed USB 3.0 xHCI Controller Until now, i don't have solution for USB 3.0 and Internal Sata. You can check the SIP status by using csrutil status Now run the Clover EFI Installer. csrutil disable Then restart your Mac again to make the change. Then open a Terminal from menu bar and type the following command. And after install it to your harddrive, you will still get "Still Waiting for Root Device" because Internal Sata Problem (and i use PCIe to Sata with ASmedia chipset AS1062 to solve this problem) To disable SIP, restart your Mac, and boot into recovery mode by holding Command-R until you see an Apple icon with progress bar. Try to use " 0x00306F2" and tick "Kernel Haswell-E or "0x00306C3" and tick "Kernel PM".īut, i think you will get "Still Waiting for root device" because USB Problem (I use PCI to USB 2.0 with NEC Chipset to solve this problem). config or clover? Is it currently compatible with Z170 Mobos? So, what does this " " mean on the screen and why the system halts? Anything I need to change in the. IABootFiles\boot.eft Using reloc block: no, hibernate wake: no " and it will reboot after the " " sign. I tried with and without OSXAptioFixDrv, the result is the same except when with OSXAptioFixDrv, I can see additional lines like "Start overriding for. The mother board is Gigabyte Z170 UD5 and I also had a GTX 970 GPU (which I think is not the reason since I also tried NV_disable = 1). However, after I select "install El Capitan from USB", I see just a line of signs (like : " " ) and the screen halts. I have been able to boot it using OpenCore but I wanted Clover as it helps me with my development process. Any help at the earliest is highly appreciatable. I use this for my Pemtium g3258 and I can do some browsing but certain websites are buggy. I was able to use it in UEFI mode and see the installer after reboot. I gave the FakeCPUID 0x0306A0 in the ist with the help of clover configurator, added the FakePCIID.kext. Because I see a section in clover called Fake Id and there is a part for graphics You could try fake CPUID 0x0306A0 and graphics inject Intel yes, Intel Id 0x04128086, ig 0x022d0003. So I downloaded it and created an El Capitan installer USB. I realized there was an update to Clover ( r3280) compatible with i7-6700K CPUs.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |